DEVELOP INEO 6500 DRIVER

Revision history After publication of this service manual, the parts and mechanism may be subject to change for improve- ment of their performance. At the same time, the punch motor M [3] rotates in the direction according to the number of punched holes. Alignment mechanism The alignment is conducted by driving the alignment claws [2] by the right angle conveyance motor M6 [5] through the belt [3] and the torque limiter [4]. Functions Punching method Stops and punches every paper No. MC turns on again [1] after the 2nd paper hits against the pre-registration roller, and turns off [2] when a predetermined time period has elapsed after the LU exit sensor PS detects the leading edge of paper, then keeps the off-status until the rear end of the 1st paper is detected by PS27 in the main body. All brand and product names may be registered trademarks or trademarks of their respective holders and are hereby acknowledged. Control The bundle clip motor M11 rotates in the forward direction to move up the bundle clip until the bundle clip upper limit sensor PS33 turns ON [2] after a specified period of time since the bundle assist motor M26 starts the assisting operation [1].

Uploader:	Nicage
Date Added:	4 February 2013
File Size:	29.81 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	47969
Price:	Free* [*Free Regsitration Required]

Toner for Develop Ineo + 6500

The main body displays the mes- sage on its operation panel when the paper full is detected. Single-sided mode The paper feed motor M switches to high speed [1] and the pick-up roller is pressed against iineo origi- nals set to the original feed tray. Heat storage accumulated in paper stacked during continuous printing may cause tacking sheets of paper sticking hard each other by toner when toner that has been fused is re-fused and adheres.

The trimmer paddle is driven by the trimmer paddle motor M System Configuration Theory of Operation Ver1. Double-sided mode back side scan at1cca Paper exiting Conveyance to the back side scanning posi- tion To print the manual completely, please, download it. Overview inei the color registration control In the color registration control, the color registration marks of each color are formed on the transfer belt outside of the largest paper area.

Functions 1 Functions Non-sort mode Exited to the main tray with no processing made. After the 3rd folding conveyance sensor PS54 turns ON, the paper is conveyed by a specified number of steps. However, while in the coupling conveyance coupling mode or while exiting paper into the sub tray sub tray modethe front door can be opened and closed. The opening keeps widening until the overcurrent of M32 is detected [4].

Scanning system After the original that is conveyed on the belt stops, the scanner moves and scans the original. The tray gate is normally set to the conveyance path to the main tray.

Toner cartridge for Develop Ineo +

Food and Drug Develoo istration implemented regulations for laser products manufactured since August 1, Image Processing Theory of Operation Ver1.

Connect power plug to grounded wall outlet. There is approximately 5 mm of opening at the home position. This is a measure taken to avoid a multiple fold that is apt to occur at the folding section of paper when the 2nd folding is made.

The develoo arm home 600 PS32 [1] detects the home position of the bundle arm. Main tray paper detection The tray upper limit sensor PS2 and the stapler paper exit upper limit sensor PS7 maintain the distance between the upper surface of the paper exited in the main tray or the main tray upper surface when no paper is exited and the paper exit opening at a specified distance to prevent any uneven paper exit from occurring.

Theory Of Operation Ver1.

When the automatic "Erase outside of original" is turned ON Out of original auto-reading area equals to the max. PS3 Option 4 Microsoft Windows As shown below, each time interval between the edge detections is determined with the counts of clock signal, and the counts with the PS8 and those with the PS9 are recorded separately. Type Type Belt conveyance type original auto feeder B. Movement is made according to the staple mode. All specifications refer to A4-size paper of 80 gsm quality.

Two registration claws [4] conduct the registration by making the paper [14] contact [3] with the bundle registra- tion dveelop [13] from the gutter side. Its edge made of urethane rubber scrapes the toner off the drum surface. Bundle exit paper full control The bundle tray paper full sensor PS61 [1] detects the bundle exit inso full.

Legal restrictions on copying Certain types of originals must never be copied with the purpose or intent to pass copies of such originals off as the originals.

DEVELOP INEO+ SERVICE MANUAL Pdf Download.

Type Type Saddle stitching unit with fore-edge trimming and multi-folding function B. The support and availability of the listed specifications and functionalities varies depending on operating systems, applications and network protocols as well as network and system configurations.

Straight mode The entrance conveyance motor M1 and the paper exit motor M5 turn ON when a start-printing signal is sent from the main body.

Control The bundle press motor M23 rotates in the forward direction to conduct the paper press operation [2] to press the paper properly when the bundle press movement motor M17 completes the press position search [1]. PK 2 to 4 holes [12] [13] [11] [10] [11] [10] a04et2fca Punch motor M Groove of the switching cam Eccentric cam Projection of the punch blade Slide link [10] Projection of the switching cam Switching cam [11] Punch blade